Measuring Tools Used in Wood Working

Measuring Tools Used in Wood Working Points : Measuring Tools Used in Wood Working, Enlist the marking and measuring tools used in woodworking shop and briefly describe each., Marking and Measuring Tools Used in Wood Working Shop

1. Divider
2. Caliper
3. Rules
4. Miter Square
5. Combination Square
6. Marking Gauge
7. Mortise Gauge
8. Cutting Gauge
9. Bevel Square
10. Wing Compass
11. Straight Edge
12. Spirit Level
13. Trammels
14. Marking Knife

1. Divider Divider is a two-legged, steel tool by case-hardened points. Its size is calculated by the maximum distance it preserve be open between the two points. Therefore a 4 in, divider opens 4 in. among the points, a 6 in divider opens 6 in. among the points, etc. Dividers are use to inscribe circles and parts of circles to lay off distance and calculate distances. Equally points should be even in length; sharpen on an oil stone. 2. Caliper Caliper is use for measure outside and inside diameters etc, mainly where the sectional measurements cannot be taken. 3. Rules Rules of different sizes and propose are use by wood workers for measuring and setting out dimensions, but they usually work with a fourfold box-wood rule ranging from 0 to 60cm. This is graduate on equally sides in millimeters and centimeters and each fold is 15cm extended. 4. Miter Square Miter square is set thus that they calculate an angle of 45 degrees. They are prepared of all metal with a nicked-plated cease or with a steel blade. Blade varies as of 200mm to 250mm and so on to a highest of 300 mm long. 5. Combination Square Few woodworkers recommend a combination square which is like to the combination set use in bench works. It is a combination of a square, 45 degrees level, set square, rule straight edge and center finder. 6. Marking Gauge Marking gauge has single marking point. It gives a precise cut line parallel to a right edge, generally by the grain. Panel gauge is longer than the marking gauge and is use to gauge tines transversely wider surface. 7. Mortise Gauge Mortise gauge have two marking points, one fixed close to to the end of the stem and second attached to a brass sliding bar. These two teeth cut two similar lines call Mortise Line. 8. Cutting Gauge Cutting gauge has a cutting blade detained in place by a hold so that its ledge perhaps varied for the depth of cut. This gauge is helpful for gauging very well deep lines for such joints as dovetails on wide wood, for the edges of grooves for inlaying, cutting during very thin stuff to make little strips and cutting small rebate. 9. Bevel Square Bevel square is like to the try square except has a blade that might be swivel to any angle 0° to 180°. This tool is familiar by free by a turn screw of proper size in a machine screw operation in a slot in the blade. 10. Wing Compass Wing compass is serene of two finely pointed steel legs which are put to the preferred position and held by a set screw and quadrant. They are used while step off a number of equal space, mark circles or arcs and as scribing parallel lines to straight or bent work. 11. Straight Edge Straight edge is a machined plane part made of wood otherwise metal having truly straight and parallel edges. One of the longitudinal edges is usually made leveled. This is use to test the trueness of large surfaces and edges. 12. Spirit Level Sprit level also knows n as Plumb bob. These are use for testing the place of large surfaces. Spirit level tests intended for horizontal position. Plumb bob test for vertical place. Combination of these two give a right angle, and they are use where a try square would be far also small. 13. Trammels Trammels is a large circle or an arc have a huge radius can be tense with a tool call Trammel Points. It is every so often calling a Beam compass or Beam Trammel and can too be use to measure distances in the similar way to a divider is use. The size of the circle or arc that can be finished or the distance that can be calculated depends on the length of the beam. 14. Marking Knife Marking knife is use for change the pencil lines into cut lines. They are prepared of steel having one end pointed and the other end bent into a pointed cutting edge.